Fire Service Instruction with Eric Makowski

Straight talk on fire service instruction

Cold Weather Changes the Rules, Starting With Your Pump

By Eric Makowski


There’s an old line that the fire doesn’t care what the weather is doing. That’s true. But your pump cares, your foam cares, your hose cares and your footing cares, and every one of them behaves differently once the temperature drops below freezing.

Water that stops moving starts freezing

Everything in cold-weather operations comes back to one fact. Water at rest in a cold pump, a cold line or a cold nozzle will freeze, and it doesn’t take long. A pump that’s charged and sitting idle while the crew waits on an assignment is a pump that’s building ice.

That’s why crews who work in real winters keep water moving. Leave a discharge or a tank-fill cracked so the pump keeps circulating. Crack nozzles slightly when lines are charged and waiting. Know where your pump’s heating system or heat exchanger is and make sure it’s actually doing its job. When the evolution is done, drain the pump and the lines the way your manufacturer and your SOPs call for, and don’t skip a drain because everybody’s cold and wants to go inside.

Frozen hose is its own problem. A line that’s iced up can crack if you force it into a tight fold or try to reload it like it’s July. Sometimes the right answer is to bring it back in the shape it’s in, thaw it out and deal with it later. A damaged length you didn’t notice will show up again at the worst possible time.

Foam doesn’t flow the same in the cold

This is the one that catches ARFF crews off guard. Foam concentrate gets thicker as it gets colder. Thicker concentrate doesn’t move through a proportioning system the same way, and depending on your system, that can mean you’re mixing leaner than you think. A lean mix makes a weaker blanket, and a weaker blanket is exactly what you don’t want on a fuel fire.

Every concentrate has a temperature range it’s rated for. Know what yours is. Read the manufacturer’s data, know how your apparatus keeps concentrate within that range and find out how your proportioning system behaves when it’s cold. If your department does proportioning tests, think about what the conditions were when you last ran one. A test done on a mild afternoon tells you how the system works on a mild afternoon.

The water side matters, too. Turrets, bumper nozzles and undertruck nozzles that sit with water in them can freeze up. More than one driver has gone to flow a turret on a cold morning and gotten nothing. Cycle them, check them and know your apparatus’s cold-weather procedures before you need them on a response.

The ground is working against you

Ice on a ramp, a driveway or a training pad changes everything about how you move. Apparatus need more distance to stop. Hose lines snake on slick pavement. Firefighters carrying tools or advancing a charged line lose their footing. And the water you’re flowing during an evolution is busy making more ice the whole time.

Plan for it. Think about where runoff is going to go and where it’s going to freeze. Sand or treat walking paths and work areas before the evolution starts, not after somebody goes down. Slow the apparatus down on approach and give yourself more room when you set up. If you’re positioning on an aircraft or a structure, remember that a spot that looked solid when you pulled in might be a sheet of ice twenty minutes later.

Your people need watching, too. Wet gear freezes. Hands go numb and lose dexterity, which makes couplings, tools and SCBA straps harder to work. Facepieces can fog. Fatigue sets in faster when the body is fighting the cold and the work at the same time. Rotate crews more often, get them out of the wind between evolutions and keep spare dry gloves and hoods close.

Train in it before you respond in it

A lot of departments slow their outdoor training way down in the winter. That’s understandable, and sometimes it’s the right call for safety. But if the only time your crew pumps, flows foam or advances lines in freezing weather is on a real emergency, they’re learning cold-weather operations live.

Pick a cold day and run a short, controlled evolution with a clear objective. Charge a line and let it sit, then see what happens. Flow your turrets. Practice draining and reloading hose with cold hands. Walk the crew through what changes on your apparatus when it’s below freezing. Keep it brief, keep a warm place nearby and debrief what you found. You’ll learn more about your equipment in an hour on a cold morning than in a week of reading the manual.

What to do before the first hard freeze

Sit down with your drivers and go through every apparatus. Confirm the pump heating systems work. Review your draining procedures. Check the rated temperature range of your foam concentrate and how you keep it there. Stock sand or ice melt where you train. Then get your crew outside for one cold-weather evolution before winter makes the decision for you. The fire won’t wait for better weather, so your training shouldn’t either.

Stay safe, and train like it matters.

Eric Makowski

Eric Makowski has spent 29 years in the fire service and writes every Monday, Wednesday and Friday about fire instruction: how we teach, how we train, and how we can do both better. More about Eric →

Leave a Reply